RNA-Seq is a method to sequence RNA by applying Next Generation Sequencing (NGS). The quality of RNA is critical for the success of RNA-Seq. The integrity of RNA is measured by the RNA integrity number (RIN). RIN is computed from RNA electrophoresis and electropherogram profiles (the peak area of the 28S rRNA should be approximately twice the peak area of the 18S rRNA). If you get the RIN value lower than 7, the possibility of getting the low quality of RNA-seq data is high. To get a high quality RNA, it is better to work with fresh samples or snap-freeze the tissues in liquid nitrogen as quickly as possible and store them at -80°C until further use. Make sure designated areas and all your filter tips, microfuge tubes, plastic, and glassware are RNase-free.
Hello! I used Trizol to extract total RNA from in-vitro cultured bacteria (1 X 10^8 cells). After phase separation, I mixed ~0.4 ml of the upper phase which contains RNA with 0.5 mL cold isopropanol. However, the amount of RNA when measured in Nanodrop was very low. In addition, the ratio between 260 and 230 was around 0.1 to 0.5. Is there a chance that my sample was contaminated by the Trizol reagent? When I collected the aqueous phase I made sure to not touch the lower phase. What should I do?
The estimation of DNA methylation level heavily depends on the complete conversion of non-methylated DNA cytosines. It is crucial to ensure complete conversion of non-methylated cytosines in DNA. Therefore, it is important to incorporate controls for bisulfite reactions, as well as to pay attention to the appearance of cytosines in non-CpG sites after sequencing, which is an indicator of incomplete conversion.
In ChIP, the most vital step is the binding of an antibody and choosing the right antibody. The binding affinity of different types of immunoglobulins to protein A or G differs significantly. Henceforth, it is recommended to choose either protein A or protein G coated beads. If you do not see any product in the positive control, add 5–10 μg of chromatin and 1–5 μg of antibody to each IP reaction and incubate with antibody overnight and an additional 2 hr after adding Protein G/A beads. If no product in the experimental, add more DNA to the PCR reaction or increase the number of amplification cycles. Choose an alternate, ChIP-validated antibody if the antibody does not work.
In ChIP, the most vital step is the binding of an antibody and choosing the right antibody. The binding affinity of different types of immunoglobulins to protein A or G differs significantly. Henceforth, it is recommended to choose either protein A or protein G coated beads. If you do not see any product in the positive control, add 5–10 μg of chromatin and 1–5 μg of antibody to each IP reaction and incubate with antibody overnight and an additional 2 hr after adding Protein G/A beads. If no product in the experimental, add more DNA to the PCR reaction or increase the number of amplification cycles. Choose an alternate, ChIP-validated antibody if the antibody does not work.
In ChIP, the most vital step is the binding of an antibody and choosing the right antibody. The binding affinity of different types of immunoglobulins to protein A or G differs significantly. Henceforth, it is recommended to choose either protein A or protein G coated beads. If you do not see any product in the positive control, add 5–10 μg of chromatin and 1–5 μg of antibody to each IP reaction and incubate with antibody overnight and an additional 2 hr after adding Protein G/A beads. If no product in the experimental, add more DNA to the PCR reaction or increase the number of amplification cycles. Choose an alternate, ChIP-validated antibody if the antibody does not work.
In ChIP, the most vital step is the binding of an antibody and choosing the right antibody. The binding affinity of different types of immunoglobulins to protein A or G differs significantly. Henceforth, it is recommended to choose either protein A or protein G coated beads. If you do not see any product in the positive control, add 5–10 μg of chromatin and 1–5 μg of antibody to each IP reaction and incubate with antibody overnight and an additional 2 hr after adding Protein G/A beads. If no product in the experimental, add more DNA to the PCR reaction or increase the number of amplification cycles. Choose an alternate, ChIP-validated antibody if the antibody does not work.
In ChIP, the most vital step is the binding of an antibody and choosing the right antibody. The binding affinity of different types of immunoglobulins to protein A or G differs significantly. Henceforth, it is recommended to choose either protein A or protein G coated beads. If you do not see any product in the positive control, add 5–10 μg of chromatin and 1–5 μg of antibody to each IP reaction and incubate with antibody overnight and an additional 2 hr after adding Protein G/A beads. If no product in the experimental, add more DNA to the PCR reaction or increase the number of amplification cycles. Choose an alternate, ChIP-validated antibody if the antibody does not work.
In ChIP, the most vital step is the binding of an antibody and choosing the right antibody. The binding affinity of different types of immunoglobulins to protein A or G differs significantly. Henceforth, it is recommended to choose either protein A or protein G coated beads. If you do not see any product in the positive control, add 5–10 μg of chromatin and 1–5 μg of antibody to each IP reaction and incubate with antibody overnight and an additional 2 hr after adding Protein G/A beads. If no product is observed in the experimental sample, add more DNA to the PCR reaction or increase the number of amplification cycles. Furthermore, if you have any problem with antibodies, make sure to use the ChIP-validated antibody.
Fill out your contact details and receive price quotes in your Inbox
Outsource experiment