No discussions found
Start your discussion
Share your thoughts or question with experts in your field
Start a discussion
Found 3 matching solutions for this experiment
| Upstream tips |
Protocol tips |
Downstream tips |
-Store the unopened kit at 2-8 °C.
-Bring all reagents to room temperature before use.
-Reconstitute the Human Cytochrome c Standard with deionized or distilled water. Allow the standard to sit for a minimum of 15 minutes with gentle agitation prior to making dilutions. |
-When mixing or reconstituting protein solutions, always avoid foaming.
-Substrate Solution should remain colorless until added to the plate.
-Keep Substrate solution protected from light.
-Stop Solution should be added to the plate in the same order as the Substrate Solution.
-Wells that are green in color indicate that the Stop Solution has not mixed thoroughly with
the Substrate Solution. |
|
| Upstream tips |
-Store the unopened kit at 2-8 °C.
-Bring all reagents to room temperature before use.
-Reconstitute the Human Cytochrome c Standard with deionized or distilled water. Allow the standard to sit for a minimum of 15 minutes with gentle agitation prior to making dilutions. |
| Protocol tips |
-When mixing or reconstituting protein solutions, always avoid foaming.
-Substrate Solution should remain colorless until added to the plate.
-Keep Substrate solution protected from light.
-Stop Solution should be added to the plate in the same order as the Substrate Solution.
-Wells that are green in color indicate that the Stop Solution has not mixed thoroughly with
the Substrate Solution. |
| Upstream tips |
Protocol tips |
Downstream tips |
-All components of this kit except the standard are stable at 4˚C.
The standard must be stored at or below -20˚C.
-Bring all reagents except the
standard and assay buffer to
room temperature for at least
30 minutes prior to opening. |
-Diluted standards and samples should be kept on ice and used within 60 minutes of preparation for optimal performance. If ice is not available, diluted standards and samples should be used within 20 minutes of preparation.
-Prior to the addition of antibody, conjugate or substrate, ensure there is no residual wash buffer in the wells. Remaining wash buffer may cause variation in assay results. |
|
| Upstream tips |
-All components of this kit except the standard are stable at 4˚C.
The standard must be stored at or below -20˚C.
-Bring all reagents except the
standard and assay buffer to
room temperature for at least
30 minutes prior to opening. |
| Protocol tips |
-Diluted standards and samples should be kept on ice and used within 60 minutes of preparation for optimal performance. If ice is not available, diluted standards and samples should be used within 20 minutes of preparation.
-Prior to the addition of antibody, conjugate or substrate, ensure there is no residual wash buffer in the wells. Remaining wash buffer may cause variation in assay results. |
| Upstream tips |
Protocol tips |
Downstream tips |
-Bring all reagents and samples to room temperature (18–25 °C)
before use. |
-Wash by filling each well with Wash Buffer (300 µl) using a
multi-channel Pipette or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Buffer by aspirating or decanting. Invert the plate and blot it against clean paper towels.
-Read at 450 nm immediately after adding STOP solution. |
|
| Upstream tips |
-Bring all reagents and samples to room temperature (18–25 °C)
before use. |
| Protocol tips |
-Wash by filling each well with Wash Buffer (300 µl) using a
multi-channel Pipette or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Buffer by aspirating or decanting. Invert the plate and blot it against clean paper towels.
-Read at 450 nm immediately after adding STOP solution. |
Can't find the product you've used to perform this experiment? It would be great if you can help us by
Adding a product!